Free shipping by J&T Express for orders overRM100.00
Sort by
Show result
  • Size: 50x25x10mm
  • Material: Aluminium
  • Surface: Black Anodized
  • Weight: 13g
  • NPN power transistor in TO-220
  • New enhanced series
  • High switching speed
  • hFE improved linearity
  • hFE Grouping
  • Low power consumption
  • Power supply for 2 ~ 5.5V DC, suitable for Raspberry pi and Arduino
  • Can replace the traditional touch of a button
  • Four M2 screws positioning holes for easy installation
  • Chipset: TP4056
  • Input voltage: 4.5V~5.5V
  • Fully charged voltage: 4.2V
  • Charging current: 1A adjustable
  • Working temperature: -10'C~85'C
  • Three series of lithium battery protection board.
  • Automatically cancel protection after protection conditions restore.
  • With function of overcharge protection, over discharge protection, short circuit protection, over-current protection.
  • Suitable for lithium battery pack of 11.1V, 12V, 12.6V.
  • Quiescent current < 30uA, so power consumption is small.
  • The is super strong magnet
  • Very useful for DIY projects
  • Rating: N35
  • Size: 5(D)x5(T) mm
  • Weight: 1g
  • Type: Multilayer ceramic capacitor
  • Value available: 20pF, 22pF, 200pF, 220pF, 2.2nF, 22nF, 220nF, 2.2uF (Select in option)
  • Rated voltage: 50V
  • Contact pin pitch: 5.08mm
  • Auto DC-DC step up / down converter power module
  • Output voltage build in high-precision potentiometer for adjustment
  • Output voltage remian constant even input voltage change
  • 400KHz switching frequency
  • Up to DC 35V, 3A output
  • Good to stabilize inconsistent voltage source like battery, solar panel and wind generator
  • Mounting size: 22mm
  • Color avalable: Red, Yellow, Blue, Green, White (select in option)  
  • Insulation resistance: >= 2M ohms
  • Permitted Voltage: DC 24V 
  • Brightness: >= 100cd/m2 
  • Electrical Life: 30000 hours 
  • Protection grade: IP65
  • MY2N is industrial common uses relay found in all type of industrial equipment.
  • Very reliable and suitable for long term use.
  • Contact can switch up to 240VAC 5A load.
  • 12VDC, 24VDC or 240VAC model available.
  • Suitable for use in power hungry device, such as RS-775 DC motor, heater, pump, TEC.
  • Non-wicking, closed bottom design gives protection against flux and
  • solder contamination
  • Protected open entry for easy insertion of IC's by hand or
  • by automatic insertion
  • Anti-overstress design protects contacts, helps eliminate damage from
  • oversize leads and maintains consistent normal force
  • High normal force results in gas tight connections
  • The is super strong magnet
  • Very useful for DIY projects
  • Rating: N35
  • Size: 10(D)x10(T) mm
  • Weight: 6g
  • Wide range input voltage: 4.5V to 32V
  • Adjustable output voltage: 5V to 35V
  • Step up converter, Vout > (Vin + 1V)
  • Maximum output current (No Display): Peak: 3A [Heatsink required], Continuous: 2A
  • Maximum output current (With Display): Peak: 4A [Heatsink required], Continuous: 3A
  • Output voltage ripple: 30mV
  • Switching frequancy: 400KHz
  • Efficiency: 92% max
  • Rated Power: 20W
  • Operating temperature: -45ºC to +85ºC
  • Dimension (No Display): 43x21x14mm
  • Dimension (With Display): 60x35mmx14mm
  • Weight (No Display): 12g
  • Weight (With Display): 24g
  • Supply Voltage: 3.3. to 5 VDC
  • Operating Current: about 50mA
  • Measurement Range: 0 to 1024 deg C (32 deg F to 1875 F)
  • Measurement Resolution: +/- 0.25 Deg C (+/- 0.45 Deg F)
  • Output: Uses a SPI Interface
  • Sensor: Type K Thermocouple 
  • For point to point DIY soldering 
  • Finely drilled
  • Tough
  • Including power pad
  • Clean hole